bravoferro.blogg.se - Adjusting the taylormade rocketballz driver

#Adjusting the taylormade rocketballz driver how to
#Adjusting the taylormade rocketballz driver driver

The settings between the LOWER and UPRT markings alter the lie angle to 58.5° and 59.25°.

The settings between the STD LOFT and LOWER markings change the lie angle to 56.5° and 57.25°.These settings adjust the lie angle in smaller increments from the default lie angle and either open or close the clubface with a decrease or increase in the loft. Line the arrowhead with your preferred marking between the LOWER and STD LOFT markings, the UPRT and LOWER markings, the HIGHER and UPRT markings or the STD LOFT and HIGHER markings.The loft doesn’t get changed and the clubface is square at impact.

#Adjusting the taylormade rocketballz driver driver

The driver is the most upright in this position. This increases the default lie angle by 4° to the maximum value of 60°. However, the clubface opens or closes by 4° depending on whether the loft is decreased or increased.Line the arrowhead with the UPRT mark on the four-degree sleeve. These two settings raise the stated lie angle by a couple of degrees to 58°. Line the arrowhead marking on the clubhead with the HIGHER or LOWER marking on the hosel adapter or four-degree sleeve.Remove the clubhead from where it is seated above the four-degree sleeve.Rotate the wrench to the right side until you notice that the screw has become loose.Place the tip of the wrench into the large screw housed behind the head of the driver.

#Adjusting the taylormade rocketballz driver how to

The following steps offer a walkthrough of how to increase the default 56° lie angle of the TaylorMade M4 driver. Each movement of the sleeve alters the lie angle by 0.5° to 0.75° along with an appropriate change to the loft. The lie angle of the TaylorMade M4 driver can be changed by using the four-degree sleeve on the hosel of the driver and the accompanying wrench. The lie angle is the same for these drivers. The above adjustments are also applicable for the other variants of the TaylorMade M4 driver with 8.5°, 9.5° and 10.5° lofts. The table given below has the standard loft, lie angle and face angles of a TaylorMade M4 driver with 12° loft along with the eleven other settings for the same parameters. The clubface opens up when the loft is lowered and closes when the loft is raised. The lie angle and face angle change along with a change to the loft. The driver is likely to get damaged if you turn beyond this stage.

End the turning process when you hear a click sound.

Turn the wrench the same amount of times in a clockwise direction.

Put the wrench again into the screw as you did earlier.

Reseat the clubhead over the hosel adapter taking care not to change the above setting.

The LOWER and HIGHER settings help to set the loft of the driver to the lowest and highest possible values. This will change the lie angle and face angle.

Align the arrow marking on the clubhead with any marking apart from the STD LOFT marking present on the hosel adapter.

Lift the clubhead gently from its position above the club hosel.

You may have to turn the wrench a few times before the screw becomes loose.

Turn the wrench anticlockwise or to the right until the screw gets loosened.

Put the TaylorMade wrench into the big screw at the rear of the driver’s clubhead.

The steps below will show you how to adjust the TaylorMade M4 driver using the wrench that comes with the driver. The adjustment either increases or decreases the loft from the stated value while the lie angle always increases from the standard-setting. The four-degree sleeve supports twelve sleeve movements to change the loft and lie angle by 0.5° to 0.75° as well as the face angle by 1° to 2°. The TaylorMade M4 driver can be adjusted using its adjustable hosel that features a four-degree sleeve for its adjustment. It’s possible to have twelve different options for the loft, lie angle and face angle, including the standard settings, for the same driver using its hosel. Yes, the TaylorMade M4 driver is adjustable.